Intelligent Fixture Rigging - Revision history

Angus Ireland: /* Connect Fixtures */

2013-06-10T16:19:05Z

Connect Fixtures

← Older revision		Revision as of 16:19, 10 June 2013
Line 116:		Line 116:
	The architectural fixtures can be powered from a conventional 13 A socket. However, only one fixture can be powered from each socket, and '''multiple fixtures cannot be powered from the same double socket.'''		The architectural fixtures can be powered from a conventional 13 A socket. However, only one fixture can be powered from each socket, and '''multiple fixtures cannot be powered from the same double socket.'''
	==Connect Fixtures==		==Connect Fixtures==
	All intelligent fixtures require a DMX connection for control (although some, such as the architectural fixtures, have built-in presets and controls that can be used instead)		All intelligent fixtures require a [[DMX]] connection for control (although some, such as the architectural fixtures, have built-in presets and controls that can be used instead)

	Connect the fixtures using DMX cable to a desk, the ~~octo-splitter~~, or an existing connected fixture. Pay attention to the direction of the cable (the male end of a cable always points towards the desk, and the female end towards the end of the chain) and the number of pins (use an adaptor if necessary).		Connect the fixtures using DMX cable to a desk, the optosplitter, or an existing connected fixture. Pay attention to the direction of the cable (the male end of a cable always points towards the desk, and the female end towards the end of the chain) and the number of pins (use an adaptor if necessary).

	A DMX terminator should be fitted to the "Out/Thru" socket of the last fixture in a chain. This is a resistor that is required for DMX to function correctly. Although some fixtures will automatically do this if they are last in the chain, one should always be fitted to make sure the chain is terminated properly.		A DMX terminator should be fitted to the "Out/Thru" socket of the last fixture in a chain. This is a resistor that is required for DMX to function correctly. Although some fixtures will automatically do this if they are last in the chain, one should always be fitted to make sure the chain is terminated properly.

Angus Ireland: /* Moving Mirrors */

2013-06-10T15:56:51Z

Moving Mirrors

← Older revision		Revision as of 15:56, 10 June 2013
Line 21:		Line 21:

	===Moving Mirrors===		===Moving Mirrors===
	Moving mirror fixtures, or "scanners", are not used as often as moving heads. Examples include the ~~Martin~~ [[Martin Roboscan 518\|518s~~]] and [[Martin Destroyer\|Destroyers~~]] and the [[Technobeam]]s.		Moving mirror fixtures, or "scanners", are not used as often as moving heads. Examples include the [[Martin Roboscan 518\|Martin 518s]] and the [[Technobeam]]s.

	Moving mirror fixtures can only be rigged hanging down from a rigging point. Although they can stand upright, the DMX sockets and ventilation fans are often located on the bottom surface, so they cannot be used in this way.		Moving mirror fixtures can only be rigged hanging down from a rigging point. Although they can stand upright, the DMX sockets and ventilation fans are often located on the bottom surface, so they cannot be used in this way.

Angus Ireland: /* Architectural Fixtures */

2013-06-10T15:51:14Z

Architectural Fixtures

← Older revision		Revision as of 15:51, 10 June 2013
Line 26:		Line 26:

	===Architectural Fixtures===		===Architectural Fixtures===
	There are several architectural wash fixtures in the Union, occasionally used in Venue 1 or around the Union. They are used to wash large surfaces/areas, such as a screen or exterior wall of the building. The two types present are ~~Kolorados~~ and City ~~Colors~~.		There are several architectural wash fixtures in the Union, occasionally used in Venue 1 or around the Union. They are used to wash large surfaces/areas, such as a screen or exterior wall of the building. The two types present are [[Kolorado]]s and [[City Color]]s.

	The architectural fixtures are stored in their own wheeled flight cases. These fixtures are always rigged upright, and are always rigged in their flight cases - the lid is removed to allow use of the fixture.		The architectural fixtures are stored in their own wheeled flight cases. These fixtures are always rigged upright, and are always rigged in their flight cases - the lid is removed to allow use of the fixture.

	These fixtures are very heavy, so should only be transported using the flight cases. If they need to be lifted onto a different level, such as onto the stage, then an absolute minimum of two people is required, although 3-4 people is recommended.		These fixtures are very heavy, so should only be transported using the flight cases. If they need to be lifted onto a different level, such as onto the stage, then an absolute minimum of two people is required, although 3-4 people is recommended.

	===Others===		===Others===
	There are a number of other intelligent fixtures, such as Martin Destroyers.		There are a number of other intelligent fixtures, such as Martin Destroyers.

Angus Ireland: /* Moving Mirrors */

2013-06-10T15:32:39Z

Moving Mirrors

← Older revision		Revision as of 15:32, 10 June 2013
Line 21:		Line 21:

	===Moving Mirrors===		===Moving Mirrors===
	Moving mirror fixtures, or "scanners", are not used as often as moving heads. Examples include...		Moving mirror fixtures, or "scanners", are not used as often as moving heads. Examples include the Martin [[Martin Roboscan 518\|518s]] and [[Martin Destroyer\|Destroyers]] and the [[Technobeam]]s.

	Moving mirror fixtures can only be rigged hanging down from a rigging point. Although they can stand upright, the DMX sockets and ventilation fans are often located on the bottom surface, so they cannot be used in this way.		Moving mirror fixtures can only be rigged hanging down from a rigging point. Although they can stand upright, the DMX sockets and ventilation fans are often located on the bottom surface, so they cannot be used in this way.

	===Architectural Fixtures===		===Architectural Fixtures===
	There are several architectural wash fixtures in the Union, occasionally used in Venue 1 or around the Union. They are used to wash large surfaces/areas, such as a screen or exterior wall of the building. The two types present are Kolorados and City Colors.		There are several architectural wash fixtures in the Union, occasionally used in Venue 1 or around the Union. They are used to wash large surfaces/areas, such as a screen or exterior wall of the building. The two types present are Kolorados and City Colors.

Angus Ireland: /* Moving Heads */

2013-06-10T15:26:01Z

Moving Heads

← Older revision		Revision as of 15:26, 10 June 2013
Line 16:		Line 16:
	This article aims to cover the basic techniques of rigging intelligent fixtures, and will cover the different ways each can be rigged.		This article aims to cover the basic techniques of rigging intelligent fixtures, and will cover the different ways each can be rigged.
	===Moving Heads===		===Moving Heads===
	Moving head fixtures make up the majority of fixtures in Venue 1. These include both spot and wash fixtures, and examples include the [[Alpha ~~Spots~~]], [[Alpha ~~Washes~~]], [[Pro ~~Spots~~]] and [[5-~~Stars~~]]		Moving head fixtures make up the majority of fixtures in Venue 1. These include both spot and wash fixtures, and examples include the [[Alpha Spot]]s, [[Alpha Wash]]es, [[Pro Spot]]s and [[5-Star]]s

	Moving head fixtures can either be rigged hanging down from a bar, truss or other rigging point,supported by clamps; or upright on a flat, solid surface such as [[Nivodeck]] or the floor.		Moving head fixtures can either be rigged hanging down from a bar, truss or other rigging point,supported by clamps; or upright on a flat, solid surface such as [[Nivodeck]] or the floor.

Angus Ireland: /* Moving Heads */

2013-06-10T15:25:44Z

Moving Heads

← Older revision		Revision as of 15:25, 10 June 2013
Line 16:		Line 16:
	This article aims to cover the basic techniques of rigging intelligent fixtures, and will cover the different ways each can be rigged.		This article aims to cover the basic techniques of rigging intelligent fixtures, and will cover the different ways each can be rigged.
	===Moving Heads===		===Moving Heads===
	Moving head fixtures make up the majority of fixtures in Venue 1. These include both spot and wash fixtures, and examples include the Alpha Spots, Alpha Washes, Pro Spots and 5-Stars		Moving head fixtures make up the majority of fixtures in Venue 1. These include both spot and wash fixtures, and examples include the [[Alpha Spots]], [[Alpha Washes]], [[Pro Spots]] and [[5-Stars]]

			Moving head fixtures can either be rigged hanging down from a bar, truss or other rigging point,supported by clamps; or upright on a flat, solid surface such as [[Nivodeck]] or the floor.

	~~Moving head fixtures can either be rigged hanging down from a bar, truss or other rigging point,supported by clamps; or upright on a flat, solid surface such as Nivodeck or the floor.~~
	===Moving Mirrors===		===Moving Mirrors===
	Moving mirror fixtures, or "scanners", are not used as often as moving heads. Examples include...		Moving mirror fixtures, or "scanners", are not used as often as moving heads. Examples include...

Alistair at 12:08, 9 June 2013

2013-06-09T12:08:26Z

@@ Line 59: / Line 59: @@
 When rigging moving head fixtures upright, any clamps fitted must be removed.
-===Addressing===
+When rigging any other moving head fixture, unbolt the clamp from the base of the fixture.
-==Rigging==
+This can only be done by hand if the rigging point is no higher than head height. If the rigging point is any higher, use a rope!
 ==Rigging Upright==
 ==Addressing etc.==
 ==De-Rigging==
 ==Extra==

Alistair at 11:28, 9 June 2013

2013-06-09T11:28:00Z

← Older revision		Revision as of 11:28, 9 June 2013
Line 55:		Line 55:
	Moving head fixtures should be fitted with '''two''' clamps (of the same type/size), spaced approximately 15 cm apart, and bolted into mounting holes on the fixture or on an adaptor on the base of the fixture (speak to a senior member of the crew if you are unsure about this).		Moving head fixtures should be fitted with '''two''' clamps (of the same type/size), spaced approximately 15 cm apart, and bolted into mounting holes on the fixture or on an adaptor on the base of the fixture (speak to a senior member of the crew if you are unsure about this).

			Moving mirror fixtures, and other intelligent fixtures that can be rigged this this fashion, have a yoke, to which the clamp should be bolted. Follow the same procedure as with a generic fixture.
			====Upright====
			When rigging moving head fixtures upright, any clamps fitted must be removed.



	~~====Upright====~~
	===Addressing===		===Addressing===

Line 67:		Line 68:
	==Addressing etc.==		==Addressing etc.==
	==De-Rigging==		==De-Rigging==
			==Extra==
			Moving heads: nose down
	==Safety Guidelines==		==Safety Guidelines==
	[[Category:How To]][[Category:Unfinished]]		[[Category:How To]][[Category:Unfinished]]

Alistair at 11:22, 9 June 2013

2013-06-09T11:22:18Z

@@ Line 43: / Line 43: @@
 If the fixture is to be rigged suspended from a bar/truss, it must be fitted with clamps.
-The most common type of clamp used for moving head fixtures is a circular Cheeseborough clamp, also called a pipe clamp or C-clamp ("pipe clamp" will be used for the rest of this article).  These are able to support the
+The most common type of clamp used for moving head fixtures is a circular Cheeseborough clamp, also called a pipe clamp or C-clamp ("pipe clamp" will be used for the rest of this article).  These are able to support the fixture and cope with any movement introduced when the fixture is in use.
 ====Upright====
 ===Addressing===

Alistair at 11:14, 9 June 2013

2013-06-09T11:14:43Z

← Older revision		Revision as of 11:14, 9 June 2013
Line 29:		Line 29:

	These fixtures are very heavy, so should only be transported using the flight cases. If they need to be lifted onto a different level, such as onto the stage, then an absolute minimum of two people is required, although 3-4 people is recommended.		These fixtures are very heavy, so should only be transported using the flight cases. If they need to be lifted onto a different level, such as onto the stage, then an absolute minimum of two people is required, although 3-4 people is recommended.
			===Others===
			There are a number of other intelligent fixtures, such as Martin Destroyers.

			These resemble generic fixtures in shape, and should be rigged by hanging from a rigging point using a clamp.



	==Before Rigging==		==Before Rigging==
	===Check Rigging Point===		===Check Rigging Point===
	Check the area around the rigging point to make sure there are no obstructions that could make rigging difficult or hazardous. Take care when rigging near other fixtures, as these may be hot, and ensure sufficient clearance is left around intelligent fixtures to allow their full range of movement.		Check the area around the rigging point, whether it is a lighting bar or a space on the floor, to make sure there are no obstructions that could make rigging difficult or hazardous. Take care when rigging near other fixtures, as these may be hot, and ensure sufficient clearance is left around intelligent fixtures to allow their full range of movement.

	Remember to allow enough space around the fixture currently being rigged, for its full range of movement.		Remember to allow enough space around the fixture currently being rigged, for its full range of movement.
	===Prepare Fixture===		===Prepare Fixture===
			Prepare the fixture for rigging
			====Suspended====
			If the fixture is to be rigged suspended from a bar/truss, it must be fitted with clamps.

			The most common type of clamp used for moving head fixtures is a circular Cheeseborough clamp, also called a pipe clamp or C-clamp ("pipe clamp" will be used for the rest of this article). These are able to support the
			====Upright====
			===Addressing===